The Best statics Tutors in Houston, TX

Houston, TX

BS in Mechanical Engineering Technology

By a couple weeks after being first introduced to a new analytic or modeling software, I was the class expert to ask - typically had collaboration in half of the projects turned in by the entire class. I’m strong in Statics, Dynamics, Stress and Deformation Analysis, Fluid Mechanics, and Electrical-Electronic... See Bryson's full profile

Houston, TX

Cisco Netacad Instructor in CCNA since 2014

More specifically, topics I can help you with include but are not limited to IPv4 and IPv6 addressing, subnetting and VLSM, MAC addresses, ARP, the OSI model, TCP/IP protocol suite, basic hardware, static routes, OSPF, binary, ACLs, wildcard masks, DHCPv4 and DHCPv6, NAT/PAT, VLANs, trunking, inter-VLAN... See Krista's full profile

Near Houston, TX

Ace SAT/ACT, Math, Physics & Engineering with a Graduate Engineer

...GRE Quantitative ASVAB PICAT OAR I have tutored more than 500 hours of the following engineering courses on this platform Statics Dynamics Thermodynamics Fluid Mechanics (Fluid Statics and Fluid Dynamics) Heat Transfer Mechanics of Materials (Solid Mechanics or Deformable Bodies) Vibrations System Dynamics... See Zeeshan's full profile

Aerospace Engineer with 7+ years of experience

I graduated summa cum laude in Aerospace Engineering with above a 3.9 in both my undergraduate and master's degree. Potential courses I can tutor include (but are not limited to): Thermodynamics, Dynamics, Statics, Structures,... See Ryan's full profile

Bachelor of Science in Aeronautical & Astronautical Engineering

...a job offer from Lockheed Martin. I am experienced in thermodynamics, heat transfer, signal analysis, fluid mechanics, statics and dynamics, structures, control systems, and combustion processes, and can tutor all specializations and draw on insights... See Radman's full profile

Princeton Engineering PhD Tutoring Statics

I have an PhD in civil engineering from Princeton University. Statics is a fundamental part of both civil and mechanical engineering and important to understand before moving on to more challenging classes. I am experienced in teaching... See Christine's full profile

PE-Licensed Civil Engineer | Transportation Design Specialist

I hold a Bachelor of Science in Civil Engineering from Northern Arizona University, an ABET-accredited program, where I built a strong foundation in structural analysis, transportation design, hydraulics, and statics. I currently work as a... See Preston's full profile

ME Professor | Dynamics, Mech of Materials, Machine Design, Statics

... students through the most challenging parts of their undergraduate programs. My specialties are Engineering Dynamics, Statics, Mechanics of Materials, Machine Design, Mechanical Systems and Controls, and Aerodynamics. Feel free to reach out if you... See Katie's full profile

Purdue Mechanical Engineering Graduate & FE-Certified Engineer

I earned a Bachelor of Science in Mechanical Engineering from Purdue University and have passed the Fundamentals of Engineering (FE) exam. My coursework included thermodynamics, heat transfer, fluid mechanics, statics, dynamics, engineering... See JJ's full profile

Engineering Dynamics Specialist

I hold a Bachelor of Science in Mechanical Engineering and have over three years of experience tutoring core mechanical engineering courses, including Statics, Dynamics, and Mechanics of Materials. I specialize in breaking down complex... See Eric's full profile

Bachelor's Degree in Mechanical Engineering with 4+ years tutoring

I have a Bachelor's degree in Mechanical Engineering and over four years of experience tutoring core engineering subjects, including statics, thermodynamics, fluid mechanics, and mechanical systems. I work with students, guiding them... See David's full profile

Civil Engineering Tutor - Statics and Structures

I have studied Statics and Structural Analysis. In addition, I helped some clients with statics and certain other civil engineering courses, such as a numerical analysis course with civil engineering applications. In addition, I have... See David's full profile

Mechanical Engineering Professor with 41 years of experience

I have been teaching Mechanical Engineering at the college level for 41 years. The subjects that I have taught most often are Thermodynamics, Statics and Dynamics. My students always praise me for showing them the easiest way to solve... See Keith's full profile

PhD in fluid mechanics, BSE and MSE in mechanical engineering

I have BSE, MSE, and PhDs in mechanical engineering. My thesis was in computational fluid dynamics. I've been a teaching assistant for statics and strength of materials, fluid and heat transfer labs, introduction to flight (twice),... See Andrew's full profile

Harvard A.B. in Chemistry and Physics, Interdisciplinary Experience

...practical Engineering experience, to facilitate learning. I have tutored a number of engineering students in Mechanics (Statics, Dynamics, Strengths of Materials, etc), Electricity&Magnetism, Thermodynamics, Heat Transfer, and more online using these... See Jade's full profile

Senior Aerospace Engineering student with 3 years tutoring experience

I am a senior Aerospace engineering student at the University of Tennessee. I have experience tutoring fellow students in statics, thermodynamics, fluid mechanics, heat transfer, and system dynamics. See Alexander's full profile

Engineering, Education Student, Statics, Calculus, Materials, Thermo.

I'm Michael. A tutor of 5 years and a student in teaching for mathematics for half a year. I have enjoyed tutoring for this whole time. Most students come to me with some understanding of the subject, but not being able to apply it to the homework... See Michael's full profile

Extensive experience tutoring future Engineers

While working on my graduate degrees, I taught and tutored at the college level. Courses taught include Statics and Thermodynamics. In the past I have tutored engineering courses such as Statics, Dynamics, Thermodynamics, Fluid... See George's full profile

M.S., B.S, NucEng UC Berkeley, 5+ yrs Power Plant & Mech. Engineer

My education at Berkeley included Mechanical Engineering Classes in Materials Science, Mech. Engineering Drafting and Design, Mechanics - Statics and Dynamics, Civil Engineering, Thermodynamics, Fluid Mechanics/Dynamics, Mechanics of... See Dick's full profile

Statics Dynamics Strengths of Materials Thermodynamics Fluid Mechanics

I have regularly instructed Engineering Mechanics courses at Penn State including, E MCH 210, E MCH 211, E MCH 212, E MCH 213, which are the subjects of Statics, Dynamics, Strengths of Materials, Thermodynamics, and Fluid Mechanics. I have... See Douglas's full profile

Structural Engineering Masters Student with Aerospace Applications

...strong foundation in core mechanical engineering principles. My undergraduate coursework covered mechanics of materials, statics, dynamics, and fluids, while my graduate studies have expanded my expertise into advanced structural analysis and aerospace-related... See KrisAnna's full profile

Current AE & EE Graduate Student w/ 15 Years of Experience & Knowledge

I'm currently pursuing two graduate degrees in aeronautical and electrical engineering. My areas of expertise in aeronautical engineering are statics, dynamics, fluid mechanics, thermodynamics, and heat transfer. My teaching methods... See Andrew's full profile

University professor and experienced tutor

I teach courses like Statics, Fluid Mechanics, Material Properties, and Heat Transfer as an adjunct professor at different colleges. I’ve also been tutoring graduate-level Mechanical Engineering courses for the last 10 years. I’m... See Alireza's full profile

Bachelor's degree in Mechanical Engineering

I am also very, very good at translating "textbook" into English. This is especially critical when a specific method or format is required to answer a physics question, such as in statics or dynamics. See Alexis's full profile

PhD Mechanical Engineer|Solid Mechanics • Statics • Dynamics • MATLAB

I’m a dedicated educator with a PhD and MSc in Mechanical Engineering from Texas A&M University, specializing in Solid Mechanics, Statics, Engineering Dynamics, Mechanical Vibrations, Dynamic Systems & Controls, and Applied... See ANGEL's full profile